Locate pin . Grounding this wire manually turns the fuel pump on without cranking. This is perfect for draining the tank or testing fuel pressure.
| Pin | Signal | Description | |------|--------|--------------| | B1 | VTA | Throttle position sensor (TPS) signal | | B2 | VC | 5V sensor supply (TPS, MAP) | | B3 | E2 | Sensor ground | | B4 | VCC | 5V reference (MAP) | | B5 | PIM | MAP sensor signal | | B6 | THW | Coolant temp sensor signal | | B7 | THA | Intake air temp signal | | B8 | STA | Starter signal | | B9 | NSW | Neutral start switch (auto) / clutch (manual) | | B10 | SPD | Vehicle speed sensor signal | | B11 | G2 | Distributor G2 (cam position) | | B12 | G1 | Distributor G1 (cam position) | | B13 | NE+ | Distributor NE (crank position) positive | | B14 | NE- | Distributor NE negative | | B15 | IGF | Ignition confirmation signal (to ECU from igniter) | | B16 | IGT | Ignition timing signal (ECU to igniter) |
| Wire | Must Connect To | | :--- | :--- | | +B (A02), +B1 (A01) | 12V from EFI relay | | BATT (C11) | Constant 12V | | IGSW (A03) | 12V from ignition switch (RUN/START) | | STA (A10) | 12V from starter solenoid (while cranking) | | E01, E02 (A15, A16) | Engine ground | | NE+ & NE- (A24, A25) | Distributor | | G+ & G- (A22, A23) | Distributor | | SP1 (A14) | Vehicle speed sensor (or 12V via 1k resistor to trick it) | | 4 injector wires | To injectors (with constant 12V on other side) | | IGT (B01) & IGF (A26) | To igniter |
| Model Year / Market | Pinout Difference | |---------------------|--------------------| | 1988–1992 AE92 (USA) | Uses 26-pin + 12-pin. Pins shifted. Pin 13 IGF is on different slot. | | 1996–1997 OBD-II AE102 | Adds pin for secondary O2 sensor (after cat). Pin B4 becomes HO2S1. | | European Carina E | Connector pins often reversed (female on harness). Pin A16/A17 swapped. | | Geo Prizm (L-body) | Uses same 22+16 but colors differ. Use pin number, not color – GM used different wire suppliers. |
: Idle switch signal from the TPS to tell the ECU the throttle is closed. : Speed sensor signal from the instrument cluster. ⚠️ Important Wiring Considerations Generation Shifts
Toyota 4afe Ecu Pinout Jun 2026Locate pin . Grounding this wire manually turns the fuel pump on without cranking. This is perfect for draining the tank or testing fuel pressure. | Pin | Signal | Description | |------|--------|--------------| | B1 | VTA | Throttle position sensor (TPS) signal | | B2 | VC | 5V sensor supply (TPS, MAP) | | B3 | E2 | Sensor ground | | B4 | VCC | 5V reference (MAP) | | B5 | PIM | MAP sensor signal | | B6 | THW | Coolant temp sensor signal | | B7 | THA | Intake air temp signal | | B8 | STA | Starter signal | | B9 | NSW | Neutral start switch (auto) / clutch (manual) | | B10 | SPD | Vehicle speed sensor signal | | B11 | G2 | Distributor G2 (cam position) | | B12 | G1 | Distributor G1 (cam position) | | B13 | NE+ | Distributor NE (crank position) positive | | B14 | NE- | Distributor NE negative | | B15 | IGF | Ignition confirmation signal (to ECU from igniter) | | B16 | IGT | Ignition timing signal (ECU to igniter) | toyota 4afe ecu pinout | Wire | Must Connect To | | :--- | :--- | | +B (A02), +B1 (A01) | 12V from EFI relay | | BATT (C11) | Constant 12V | | IGSW (A03) | 12V from ignition switch (RUN/START) | | STA (A10) | 12V from starter solenoid (while cranking) | | E01, E02 (A15, A16) | Engine ground | | NE+ & NE- (A24, A25) | Distributor | | G+ & G- (A22, A23) | Distributor | | SP1 (A14) | Vehicle speed sensor (or 12V via 1k resistor to trick it) | | 4 injector wires | To injectors (with constant 12V on other side) | | IGT (B01) & IGF (A26) | To igniter | Locate pin | Model Year / Market | Pinout Difference | |---------------------|--------------------| | 1988–1992 AE92 (USA) | Uses 26-pin + 12-pin. Pins shifted. Pin 13 IGF is on different slot. | | 1996–1997 OBD-II AE102 | Adds pin for secondary O2 sensor (after cat). Pin B4 becomes HO2S1. | | European Carina E | Connector pins often reversed (female on harness). Pin A16/A17 swapped. | | Geo Prizm (L-body) | Uses same 22+16 but colors differ. Use pin number, not color – GM used different wire suppliers. | | | 1996–1997 OBD-II AE102 | Adds pin : Idle switch signal from the TPS to tell the ECU the throttle is closed. : Speed sensor signal from the instrument cluster. ⚠️ Important Wiring Considerations Generation Shifts |